400 watt high amp alternator made with permanent magnets. 10 watt Eco Worthy solar panel with built in charge controller. It charges and maintains your battery. 400 watt DC to AC inverter with USB ports and audible low voltage alarm.
The inverter will sound an alarm if your battery voltage gets too low. Powerful enough to charge cell phones, lap top computers, TV's, HAM radios, walkie-talkies, and any device consuming up to 400 watts. 50 amp heavy duty rectifier coverts AC current into storeable power. The pulley adjusts to the width of your rear bicycle tire, which enables you to make electricity with a stationary bike trainer.Width of the tire should not exceed 1.5 inches. Just mate the bike tire with the unit and start peddling. A bungee strap can be useful to keep the connection from separating. Battery charging cables are already installed and clearly marked +Positive & -Negative. These are nut and bolt type terminations. We recommend the EverStart model U1R 12 volt battery, or equal. A deep cycle battery is not required because the 400 watt inverter, supplied with this product, will shut off the unit if the voltage gets too low. The Battery is not included.
Combining the batteries and PMA section, the "3 in 1" is capable of delivering over 400 watts of sustained power, and 800 watts max. For starting motors, fans, pumps etc. The "3 in 1" Power Station(TM) is powerful enough to operate ham radios, water pumps, computers, cell phones, kitchen appliances, Ipads, televisions, stereos, drills and hundreds of other products consuming 400 watts or less. What's in the box?
1- 400 watt high amp EMP proof alternator. 1- 400 watt AC/DC power inverter. 1- 10 watt solar panel with charge controller. 1- 14 hand crank wheel and handle. 1- 3 adjustable pulley, for bike pedal charging.
1- Digital volt meter with on off switch. 1- Set of clearly marked battery cables, nut and bolt type. 1- Allen wrench tool set (for installing 14 wheel). Keep away from children and pets! Depending on the bike trainer model being used, you may need to elevate the generator off the floor a few inches.
FAST & EFFICIENT CHARGING ABILITY. On average, it takes 30 minutes to recharge one battery. Actual time depends on the condition of the batteries, the speed of cranking and the load being drawn.
For best results, you should always crank or pedal whenever you're drawing a load. This will minimize the amount of time required to recharge the batteries. The alternator is designed for 6-20 amps of recharge power. The lower your battery voltage gets, the more current will flow into them. Full or nearly full batteries require less current, so less is produced by the PMA.It's important to note that discharging a battery beyond it's safe limit could cause permanent damage. Never allow your batteries to become fully discharged.
The "3 in 1" unit weighs about 30 pounds without the battery. The battery compartment is 9"long, 9"high, 8wide. Overall dimensions of the case: 22L x 10H x 10W (this does not include the 14 flywheel). Our "3 in 1" unit is fully compatible with additional solar panels or wind turbines.
Diodes protect the PMA section from damage. A solar panel and/or wind turbine may be connected directly to the "3 in 1" batteries. With adequate battery amp hours, the "3 in 1" units can be used to power medical equipment such as nebulizers and CPAP machines.
It's especially important for persons living in high rise apartments or condos where gasoline generators can't be used during a power outage. Charge batteries, run lights, laptops, cell phones, TVs, CB radios, Ham radios, small kitchen appliances, power tools, you name it! If you need 120 volt current to run something up to 400 watts, the "3 in 1" units will deliver. Caution: do not allow children to operate this product! There is a risk of pinching if used improperly.Some parts may contain sharp edges. Wear eye protection and gloves. Do not operate this unit until the battery has been installed. Damage to the volt meter will result. Do not store this unit indoors where vapors from the battery could enter living spaces. Do not get the contents of this product wet. Caution- Read and follow all safety and set-up instructions on this page before using this product.
An instruction sheet is also supplied with your unit. Please call our office at 513.232.1457 if you need assistance.1- Unpack the product and place it on a flat, level surface. Inspect the contents of the generator for damage. 2- Thread the 4" black drive handle onto the 14" pulley bolt. The handle bolt is already installed on the 14 pulley. 3- Install the 14" pulley on the 3/4" drive shaft.
Applying a very thin coat of Vaseline or lubricant to the drive shaft will make the pulley easier to install. You will need an Allen wrench supplied with this product.
Do not fully tighten the pulley yet! 4- Install the drive belt. Start by putting the belt on the smaller pulley, then the larger one. Turn the handle until the belt is installed. Caution: Don't pinch your fingers!
5- With the belt installed, and both pulleys in a straight line, you can now tighten the pulleys using the Allen wrench fittings. 6- Make sure the drive belt is not too tight. This will make the unit hard to turn.
7- When the pulleys and drive belt are installed, and tightened properly, the unit should operate very smoothly. If there is a wobble, the parts may need to be re-adjusted. 8- For best results, crank the wheel whenever you are operating an appliance. This will help keep the battery from getting too low. Do not drain the battery!
The ac inverter supplied with your unit will sound an alarm when the battery is too low to operate efficiently. You must recharge the battery to the proper level before reusing your generator. Always use eye protection and gloves when operating this product!
1- Remove the drive belt from the pulleys. 2- Align the 3 generator pulley to the bicycle tire. Using an Allen wrench, loosen the Allen fitting on the pulley.
IMPORTANT This is the Allen fitting nearest to you, not the one nearest to the generator! Turn the adjustable pulley in or out, until the desired width is achieved for the bicycle tire. 3- Restrain the generator case so it doesn't move. A rubber bungee strap can be useful! 4- After connecting the battery cables you may pedal at will!
This product does not come with the bike trainer or stool. The item "3 in 1 Power 400 Watt Hand Crank Bike Pedal Solar Generator" is in sale since Wednesday, June 16, 2021. This item is in the category "Home & Garden\Home Improvement\Electrical Supplies\Alternative Energy Supplies\Solar Power Supplies\Solar Panels & Kits". The seller is "prestowind2008" and is located in Fort Thomas, Kentucky. This item can be shipped to United States.